Bailers
B & T 2 Piece Ball Bottom Specifications Sheets
The B & T 2 Piece Ball Bottom is an alternative to the normal style ball bottom used with traditional bailers. It can only be used on coarse thread bailers.
The B & T 2 Piece Ball Bottom is an alternative to the normal style ball bottom used with traditional bailers. It can only be used on coarse thread bailers.
B & T Drive-Down Bailer Specifications Sheets
The B & T Drive-Down Bailer is a simple tool consisting of a top sub, barrel, and either a ball bottom or flapper bottom. They are used to bail mud and shale by being lowered into the shale, or debris. This fills the barrel with the target debris. The Drive-Down Bailer is then is pulled to extract the debris out of the well bore.
The B & T Drive-Down Bailer is a simple tool consisting of a top sub, barrel, and either a ball bottom or flapper bottom. They are used to bail mud and shale by being lowered into the shale, or debris. This fills the barrel with the target debris. The Drive-Down Bailer is then is pulled to extract the debris out of the well bore.
B & T Dump Bailer Specifications Sheets
The B & T Dump Bailer is used to place small amounts of cement slurry, or similar material in a well bore. The Dump Bailer holds the contents in the barrel. When the Dump Bailer is jarred, the shear pin is sheared, which then turns a plunger. The plunger then shears a rupture disk and the barrel releases the contents into the well bore.
The B & T Dump Bailer is used to place small amounts of cement slurry, or similar material in a well bore. The Dump Bailer holds the contents in the barrel. When the Dump Bailer is jarred, the shear pin is sheared, which then turns a plunger. The plunger then shears a rupture disk and the barrel releases the contents into the well bore.
B & T Hydrostatic Bailer Specifications Sheets
The B & T Hydrostatic Bailer is designed to be used when a pump action bailer fails to remove the sand or debris surrounding a subsurface device. The Hydrostatic Bailer consists of a chamber that has been loaded and sealed at atmospheric pressure. When the bailer reaches the top of the sand, downward jarring shears a pin, causing bottom hole pressure to surge into the chamber, forcing the bailer piston upward. When pressure in the chamber equalizes the memory pressure gauge or other equipment, a ball check closes to retain the sand and debris in the chamber.
The B & T Hydrostatic Bailer is designed to be used when a pump action bailer fails to remove the sand or debris surrounding a subsurface device. The Hydrostatic Bailer consists of a chamber that has been loaded and sealed at atmospheric pressure. When the bailer reaches the top of the sand, downward jarring shears a pin, causing bottom hole pressure to surge into the chamber, forcing the bailer piston upward. When pressure in the chamber equalizes the memory pressure gauge or other equipment, a ball check closes to retain the sand and debris in the chamber.
B & T Maxwell-Style Bailer Specifications Sheets
The B & T Maxwell-Style Bailer is a pump action bailer designed to remove debris and sand in the tubing string through using upward jarring motion. B & T has different lengths of pump barrels as well as load barrels to suit different bailing needs. The Maxwell-Style Bailer utilizes a brass piston component to bail the debris and sand from the well bore.
The B & T Maxwell-Style Bailer is a pump action bailer designed to remove debris and sand in the tubing string through using upward jarring motion. B & T has different lengths of pump barrels as well as load barrels to suit different bailing needs. The Maxwell-Style Bailer utilizes a brass piston component to bail the debris and sand from the well bore.
B & T Sample Bailer Specifications Sheets
The B & T Sample Bailer functions the same way as a B & T Drive-Down Bailer with a much shorter barrel (typically 18”). It is commonly attached to a Tubing End Locator to take samples from the well bottom. It is able to retrieve large samples by opening the flapper or ball bottom sub, allowing the mixture to enter the barrel. The Sample Bailer then closes as it is drawn back to the surface.
The B & T Sample Bailer functions the same way as a B & T Drive-Down Bailer with a much shorter barrel (typically 18”). It is commonly attached to a Tubing End Locator to take samples from the well bottom. It is able to retrieve large samples by opening the flapper or ball bottom sub, allowing the mixture to enter the barrel. The Sample Bailer then closes as it is drawn back to the surface.
B & T Sand Bailer / Pump Bailer Specifications Sheets
The B & T Sand Bailer / Pump Bailer is a 2 piece pump action bailer, designed to remove sand and small debris in the tubing string through the upward stroking motion of the pump section. Debris is sucked into the load barrel as the assembly is jarred up. The main distinguishing component of the Sand Bailer / Pump Bailer is its wobble washer.
The B & T Sand Bailer / Pump Bailer is a 2 piece pump action bailer, designed to remove sand and small debris in the tubing string through the upward stroking motion of the pump section. Debris is sucked into the load barrel as the assembly is jarred up. The main distinguishing component of the Sand Bailer / Pump Bailer is its wobble washer.
B & T Tubing End Locator Specifications Sheets
The Tubing End Locator is used to determine the depth of the tubing using a spring-loaded finger. The finger catches the end of the tubing when pulled upward, registering as a reading on the weight indicator. Shear the pin by jarring upward on the assembly, and the finger should retract back inside the tool so that retrieval is possible.
The Tubing End Locator is used to determine the depth of the tubing using a spring-loaded finger. The finger catches the end of the tubing when pulled upward, registering as a reading on the weight indicator. Shear the pin by jarring upward on the assembly, and the finger should retract back inside the tool so that retrieval is possible.